![]() ![]() Note: Some car will not have a plug so you will need to tap into the car’s ignition wire and connect with the ignition wire of the switch harness. ![]() Connect the car’s ignition wire with the (Positive + ) (red) ignition plug of the switch harness. Remove the driver’s dashboard lower panels if necessary, then find the ignition wire of the switch harness. It’s usually on the dashboard but some locations may be near the hand brake.ġ0. Find an appropriate location to mount the switch. (Attach harnesses together with the bullet plugs.ĩ. Route the main wiring harness through the firewall, then connect to the switch wiring harness. ![]() Attach red wire (Positive + ) of main wiring harness to (Positive + ) of the battery node or to the (Positive node of the fuse box.Ĩ. Attach relay to relay connector, then attach black wire terminal (Negative - ) to the car frame to create a ground circuit. Route the main wiring harness through the engine bay to the lamp and connect with bulb. If removal of inner fender wall is required, turn your steering wheel left and right to create clearance if needed.ħ. Then install your fog lights to their proper positions.Ħ. Open the hood and remove the front bumper if necessary. Write your presets down prior to disconnecting the battery cable.ĥ. Note: Radio presets and clocks may be reset when disconnecting the battery cable. Make sure that lamps, air conditioner and other devices are switched off. Disconnect the ( Negative - ) terminal of the battery before installation. When connecting the harnesses or plugs, insert the connectors firmly until they lock securely into place.Ĥ. Bind all harnesses together so that they do not move around loosely, otherwise the harnesses may break or short circuit – accidents, electric shocks, or fire may occur.ģ. This installation requires and is not limited to an adjustable wrench, nippers, flat-tip screwdriver, Phillips screwdriver, clip remover, shop towel, cardboard or blanket.Ģ. Certain tools are required to ensure proper installation. Before beginning installation, you are expected to carefully read the instructions.ġ. The application of different fog lights for different vehicles may require a different wiring kit. This wiring kit applies only to the fog light set which it comes packaged with. We used the "most complicated" car in this video that way you can see how it is easy to install LED headlights and foglight on your pick up.OEM Aftermarket Fog Light Wiring Kit Installation HELIOS LED CONVERSION KIT INSTALLATION ON RAM 1500 (installation 10% of vehicles) Most cars are made this way and do not require to remove anything else in your car. HELIOS LED CONVERSION KIT INSTALLATION TOYOTA COROLLA (Really Easy installation 90% of vehicles) Make sure to not touch the LED chips with your hands during the installation. You will receive 3M tape and tie-wrap to make sure the LED driver is located in the area and won't be moving while you're driving. Remove the old bulbs, put in place your CLD bulbs in the same original socket and plug the LED wire to your original plug. If you have two separates bulbs make sure to differentiate Low from High beams.įor most cars, the installation process won't need to remove any other components to access to the bulbs it will be as easy as changing the original bulbs. Once you receive your LED headlights, pop the hood and locate your headlights bulbs. By scrolling down you will see all available bulbs by Car Lighting District for your car.īefore to start the installation make sure the engine is off and keys are removed from ignition. You will also see on the result page that you can convert many other halogen bulbs. Those results depend on the automotive constructor bulb fit used on your make and depending on the car you might need to purchase two separate kits to convert your high and low beams. The two possible results for headlights are as follows:ġ) Low Beam headlamp & High Beam headlamp - the high and low beams use two separate bulbsĢ) High & Low Beam headlamp - the high and low beams are combined in one bulb We made sure that we provide you with over 50 000 vehicles information that way you don't need to look out anywhere else to find the right LED bulbs for your make and model. Go to our database, CLDLED.COM to find the right LED Conversion Kit for your car. How to Convert your Halogen Headlights and Fog Light to LED Bulbs ![]()
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |